Injection molding TPU long glass fiber TPU reinforced thermoplastic urethanes The most suitable processing method of TPU is screw injection molding machine. With a single screw of normal length, a three-stage screw can produce a lot of good plasticized uniform melt. If high plasticizing capacity (production capacity) is required, a longer screw can be used. Injection molding TPU long glass fiber T...

TPU polyurethane elastomer injection molding Injection The most suitable processing method of TPU is screw injection molding machine. With a single thread of normal length, the three-section screw can produce a well-plasticized uniform melt. If high plasticizing capacity is required, TPU LONG GLASS FIBER REINFOCED THERMOPLASTIC requires the use of longer screws. Screws in the short compression zon...

At present, the modified PP materials used in automobiles at home and abroad are mainly divided into the following four varieties: (1) toughening type That is to elastomer mainly toughened modified PP material, with extremely high impact strength and low temperature toughness, mainly used for the manufacture of car bumpers. (2) filling toughening type As inorganic filler, elastomer toughening modi...

Introducation LFT-G is the product name for long fiber reinforced thermoplastic materials for injection moldings,compression molding and extrusion.Retention of fiber length in the finished part is key to the performance .Fiber length is retained by proper use of free flowing check valves,metering screws and a complete evaluation of the mold to reduce high shear and allow the materials to fill the ...

The fiber size of SFT composite material is short (1~3 mm). After the screw plasticizing and injection molding of the injection molding machine, the fiber length in the product will be further shortened (0.2~0.5 mm), the fiber retention length will be less than 0.3 mm, the size will be less than the critical length of the size, so SGF can not play a strengthening role. The fibers in the LFT compos...

Compared with other nylons, PA12 long carbon fiber composite material has low density, good low temperature resistance and wear resistance, has a certain degree of self-lubrication, and its water absorption rate is lower than other nylons. The resistance to stress cracking is better than PA6 and PA66, and it has excellent resistance to alkali, oil and grease. PA12 resin has high crystallinity, low...

Polyetheretherketone, commonly abbreviated as PEEK, is a high-performance engineering thermoplastic that belongs to the polyketone family. It is known for its excellent mechanical, thermal and chemical properties. These properties make PEEK suitable for a wide range of applications. Uses include the aerospace, automotive, medical and electronics industries. But do you know what makes it unique com...

Polyether ether ketone (PEEK) is a high polymer composed of one ketone bond and two ether bonds in the main chain structure, which is a special polymer material. With high temperature resistance, chemical corrosion resistance and other physical and chemical properties, it is a kind of semi-crystalline polymer material, which can be used as high temperature resistant structural materials and electr...

preamble In the field of automotive manufacturing, the choice of materials is crucial to the performance, durability and safety of the vehicle. With the rapid development of the automobile industry, the requirements for material properties are also increasing. PEEK as a high-performance special engineering plastic, in the context of "plastic instead of steel" and "lightweight", with its excellent ...

(1) Improper control of molding conditions If the injection pressure is too low, the injection and holding time is too short, the injection speed is too slow, the material temperature and mold temperature are too high, the cooling of the plastic part is insufficient, the temperature is too high during demolding, the temperature around the insert is too low, or there is insufficient material supply...

(1) P: Poor flow of the molten material leads to the formation of concentric flow marks resembling growth rings on the surface of injection-molded parts, centered around the gate. When low-temperature, high-viscosity molten material with poor flow performance is injected into the cavity in a semi-cured, fluctuating state through the injection port and runner, the material flows along the cavity su...

Mold temperature too low Cause: If the mold temperature is too low, the melt cools too quickly during flow, causing the glass fibers to not be fully encapsulated by the base resin and float to the surface. Solution: Increase the mold temperature appropriately to ensure the melt has sufficient fluidity to uniformly coat the glass fibers. Regularly check the mold temperature control system to ensure...