-
Demand and trend analysis of composite materials for sports equipment
2024-08-08
1. Introduction The market size and variety of sports equipment continue to expand, providing more choices for people's health and recreational life. At the same time, the research and application of composite materials have also made remarkable progress, bringing innovation and breakthroughs to all walks of life. At the intersection of these two fields, it becomes an important research topic to e...
view more
-
Intelligent and Lightweight: Carbon Fiber Composites Leading Battery Structural Innovation
2024-09-02
Carbon Fiber Reinforced Polymer (CFRP) occupies a significant position in modern industry due to its exceptional physical and mechanical properties, especially in the fields of aerospace and high-performance automotive applications. With the rapid growth of the electric vehicle (EV) and energy storage system (ESS) markets, the demand for efficient, lightweight battery systems is increasing. - Trad...
view more
-
Why do injection molded parts develop sink marks and dimples?
2024-09-02
(1) Improper control of molding conditions If the injection pressure is too low, the injection and holding time is too short, the injection speed is too slow, the material temperature and mold temperature are too high, the cooling of the plastic part is insufficient, the temperature is too high during demolding, the temperature around the insert is too low, or there is insufficient material supply...
view more
-
(Ⅰ) How to deal with flow marks on injection-molded parts?
2024-09-27
(1) P: Poor flow of the molten material leads to the formation of concentric flow marks resembling growth rings on the surface of injection-molded parts, centered around the gate. When low-temperature, high-viscosity molten material with poor flow performance is injected into the cavity in a semi-cured, fluctuating state through the injection port and runner, the material flows along the cavity su...
view more
-
(Ⅱ) How to deal with floating fibers on injection-molded parts?
2024-09-27
Mold temperature too low Cause: If the mold temperature is too low, the melt cools too quickly during flow, causing the glass fibers to not be fully encapsulated by the base resin and float to the surface. Solution: Increase the mold temperature appropriately to ensure the melt has sufficient fluidity to uniformly coat the glass fibers. Regularly check the mold temperature control system to ensure...
view more
-
The application of high-performance long glass fiber (LFT) materials in explosion-proof cameras
2024-10-28
As we all know, explosion-proof products have extremely specific requirements—explosion-proof ratings, material standards, sealing performance, functionality, certification requirements, and more. Among these, material requirements are particularly stringent. Taking explosion-proof cameras as an example, most currently use stainless steel or cast aluminum alloy for the casing, which can withstand ...
view more
-
The application of advanced composite materials in drone structural components.
2024-10-28
Unmanned Aerial Vehicle (UAV), commonly referred to as "drone," is an aircraft that is operated without a human pilot on board, using radio remote control and onboard programmed control systems, or fully or intermittently autonomous operation via onboard computers. As a new type of aircraft, drones differ from manned aircraft in terms of operational requirements and mission objectives. Drones typi...
view more
-
Overview of 8 Non-Destructive Testing (NDT) Methods for Composite Materials
2024-11-01
Composite materials are new materials created through advanced material preparation techniques that combine components with different properties in an optimized manner. In the 1940s, due to the needs of the aviation industry, fiberglass-reinforced plastics (commonly known as fiberglass) were developed, marking the beginning of the term "composite materials." After the 1950s, high-strength and high...
view more
-
Eight Ways to Reduce Injection Molding Costs
2024-11-08
1. Production Workshop The layout of the production workshop should consider two main aspects: meeting production requirements and optimizing layout based on production flow, while ensuring flexible energy use under specific production conditions. (1) Power Supply: Ensure a stable power supply with a moderate buffer to avoid excessive energy waste from unused capacity. (2) Efficient Cooling Water ...
view more
-
Long Carbon Fiber vs. Short Carbon Fiber in 3D Printing
2024-11-11
In 3D printing, both long carbon fiber and short carbon fiber are used as reinforcement materials to enhance the strength and durability of printed parts. Here’s an overview of their differences: 1. Long Carbon Fiber Long carbon fibers are continuous strands that are incorporated into the printing material. This type of fiber provides superior strength, stiffness, and structural integrity to the p...
view more
-
Do you know which nylon materials are used in new energy vehicles?
2024-11-15
In the new energy vehicle materials industry, polymers encompass plastics, rubber, silicone materials, and composite fiber materials such as carbon fiber. To avoid safety hazards associated with high-voltage systems, materials for new energy vehicles must not only be heat-resistant but also flame-retardant. Therefore, Xiamen LFT has introduced a flame-retardant polyamide solution targeting manufac...
view more
-
PEEK Shines at the Zhuhai Airshow! Applications of PEEK in Aerospace
2024-11-18
Introduction Applications of PEEK in the Aerospace Field The 15th China International Aviation and Aerospace Exhibition opened in Zhuhai on November 12, showcasing an array of major "national treasures" in the aerospace field, reflecting remarkable advancements. The airshow featured an unprecedented flight performance, with the Air Force's aerobatic team dazzling the audience. Followin...
view more
e-mail
English
français
Deutsch
русский
italiano
español
português
العربية
日本語
한국의
中文