-
The related knowledge of nylon
2023-02-23
Invention of nylon Nylon (Nylon), named Polyamide in English, is a man-made polymer. Wallace Carothers of DuPont invented the plastic on February 28, 1935, in Wilmington, USA. Nylon was officially marketed in 1938. The first nylon products were nylon brushes for toothbrushes (sold on February 24, 1938) and nylon stockings for women (sold on May 15, 1940). The appearance of nylon makes the textile ...
view more
-
In-depth analysis: 3D printing material polyamide PA nylon
2023-03-03
Nylon is a high performance polymer material in traditional industry. Nylon has also become one of the most widely used materials in 3D printing. PA6, PA11, PA12, PA66 and so on often appear in the available materials for 3D printing. In form, it is divided into powder materials which can be used for powder bed 3D printing technology, such as selective laser sintering (SLS) and multi-jet fusion (M...
view more
-
Polyamide 12 LFT: Benefits and applications
2024-01-16
What is PA12-LCF? PA12-LCF is a thermoplastic material, belonging to the nylon class. PA12-LCF is based on nylon 12, which has 12 carbon atoms in each polymer repeat unit. Nylon 12 is also known as polyamide 12 or PA12. It is a semi-crystalline material with a high melting point (180°C) and a low moisture absorption rate (0.5%). It is also resistant to chemicals, wear and impact. PA12-LCF is a mod...
view more
-
Modified PP plastic materials in the field of home appliances
2024-01-24
HIPS and ABS are the first plastic materials used in household appliances, due to the high price of HIPS and ABS resin, the market has gradually developed PP(polypropylene) modified materials suitable for household appliance parts, and partially replaced HIPS and ABS resin in household appliance products with its advantages of low cost, light weight and good performance. Now the modified PP plasti...
view more
-
Why do injection molded parts develop sink marks and dimples?
2024-09-02
(1) Improper control of molding conditions If the injection pressure is too low, the injection and holding time is too short, the injection speed is too slow, the material temperature and mold temperature are too high, the cooling of the plastic part is insufficient, the temperature is too high during demolding, the temperature around the insert is too low, or there is insufficient material supply...
view more
-
(Ⅰ) How to deal with flow marks on injection-molded parts?
2024-09-27
(1) P: Poor flow of the molten material leads to the formation of concentric flow marks resembling growth rings on the surface of injection-molded parts, centered around the gate. When low-temperature, high-viscosity molten material with poor flow performance is injected into the cavity in a semi-cured, fluctuating state through the injection port and runner, the material flows along the cavity su...
view more
-
(Ⅱ) How to deal with floating fibers on injection-molded parts?
2024-09-27
Mold temperature too low Cause: If the mold temperature is too low, the melt cools too quickly during flow, causing the glass fibers to not be fully encapsulated by the base resin and float to the surface. Solution: Increase the mold temperature appropriately to ensure the melt has sufficient fluidity to uniformly coat the glass fibers. Regularly check the mold temperature control system to ensure...
view more
-
Tsinghua University: Study on the Comprehensive Performance and Influencing Factors of Long Glass Fiber Reinforced PA66 Composites
2024-10-22
Introduction Fiber-reinforced polymer composites, due to their lightweight and high-strength characteristics, have found applications in many fields, especially in the transportation sector, where they can effectively reduce vehicle weight and better achieve energy savings and emission reductions. Among them, long glass fiber (LGF) reinforced polyamide materials (PA/LGF) are widely used in the man...
view more
-
Long Carbon Fiber vs. Short Carbon Fiber in 3D Printing
2024-11-11
In 3D printing, both long carbon fiber and short carbon fiber are used as reinforcement materials to enhance the strength and durability of printed parts. Here’s an overview of their differences: 1. Long Carbon Fiber Long carbon fibers are continuous strands that are incorporated into the printing material. This type of fiber provides superior strength, stiffness, and structural integrity to the p...
view more
-
How to increase the gloss of ABS injection-molded products?
2024-11-11
Injection Mold 1. If the mold cavity is poorly machined, with defects such as scratches, micro-pores, wear, or rough surfaces, it will affect the gloss of the plastic part. To address this, ensure precise machining of the mold to achieve a lower surface roughness for the cavity; if necessary, polish and chrome-plate the cavity. 2. If the cavity surface has oil stains, watermarks, or excessive mold...
view more
e-mail
English
français
Deutsch
русский
italiano
español
português
العربية
日本語
한국의
中文