-
Long glass fiber PP so many years, are flowing to what application field?
2022-12-01
In recent years, long glass fiber modified PP is extremely popular in the modified plastic industry. Long glass fiber reinforced PP material is cheap, has no less than the excellent performance of reinforced engineering plastics, the combination of these two points show the advantages of high cost performance, is widely favored by the industry. At present, these manufacturers have invested a lot o...
view more
-
[Prosthetics] You know what? There are three main materials for prosthesis receiving cavity
2023-02-17
The thigh prosthesis is composed of a receiving cavity, a knee joint and a connector, among which the receiving cavity is the connecting part of the stump and the prosthesis, and its constituent materials have a great influence on the experience of use. There are three main materials used to make prosthetic chambers: resin, PP sheet and carbon fiber. Each receiving cavity has different characteris...
view more
-
What properties will change when fiber reinforced material is added?
2023-02-21
Fiber reinforced plastics is one of the most common reinforced plastics. Fiber reinforced plastics usually have the following characteristics. High strength and high modulus The quantity strength and modulus of fiber reinforced are obviously improved. Such as some general plastics after reinforcement, can also be used in engineering plastics; Some engineering plastics, through fiber reinforcement,...
view more
-
High temperature resistant nylon can reduce the weight of automotive materials by 25-30%. What kinds are there?
2023-02-22
High temperature resistant nylon refers to the nylon material that can be used in the environment above 150℃ for a long time. The melting point is generally 290℃~320℃, and it maintains excellent mechanical properties in a wide temperature range and high humidity environment. High temperature resistant nylon has good wear resistance, heat resistance, oil resistance and chemical resistance. Compared...
view more
-
The related knowledge of nylon
2023-02-23
Invention of nylon Nylon (Nylon), named Polyamide in English, is a man-made polymer. Wallace Carothers of DuPont invented the plastic on February 28, 1935, in Wilmington, USA. Nylon was officially marketed in 1938. The first nylon products were nylon brushes for toothbrushes (sold on February 24, 1938) and nylon stockings for women (sold on May 15, 1940). The appearance of nylon makes the textile ...
view more
-
In-depth analysis: 3D printing material polyamide PA nylon
2023-03-03
Nylon is a high performance polymer material in traditional industry. Nylon has also become one of the most widely used materials in 3D printing. PA6, PA11, PA12, PA66 and so on often appear in the available materials for 3D printing. In form, it is divided into powder materials which can be used for powder bed 3D printing technology, such as selective laser sintering (SLS) and multi-jet fusion (M...
view more
-
Polyamide 12 LFT: Benefits and applications
2024-01-16
What is PA12-LCF? PA12-LCF is a thermoplastic material, belonging to the nylon class. PA12-LCF is based on nylon 12, which has 12 carbon atoms in each polymer repeat unit. Nylon 12 is also known as polyamide 12 or PA12. It is a semi-crystalline material with a high melting point (180°C) and a low moisture absorption rate (0.5%). It is also resistant to chemicals, wear and impact. PA12-LCF is a mod...
view more
-
Why do injection molded parts develop sink marks and dimples?
2024-09-02
(1) Improper control of molding conditions If the injection pressure is too low, the injection and holding time is too short, the injection speed is too slow, the material temperature and mold temperature are too high, the cooling of the plastic part is insufficient, the temperature is too high during demolding, the temperature around the insert is too low, or there is insufficient material supply...
view more
-
(Ⅰ) How to deal with flow marks on injection-molded parts?
2024-09-27
(1) P: Poor flow of the molten material leads to the formation of concentric flow marks resembling growth rings on the surface of injection-molded parts, centered around the gate. When low-temperature, high-viscosity molten material with poor flow performance is injected into the cavity in a semi-cured, fluctuating state through the injection port and runner, the material flows along the cavity su...
view more
-
(Ⅱ) How to deal with floating fibers on injection-molded parts?
2024-09-27
Mold temperature too low Cause: If the mold temperature is too low, the melt cools too quickly during flow, causing the glass fibers to not be fully encapsulated by the base resin and float to the surface. Solution: Increase the mold temperature appropriately to ensure the melt has sufficient fluidity to uniformly coat the glass fibers. Regularly check the mold temperature control system to ensure...
view more
-
Key Factors to Consider Before Using Fiber-filled Compounds
2024-10-07
In the design process of composite materials, a series of important factors must be considered to ensure the performance, safety, and cost-effectiveness of the final product. These factors include material selection, structural design, manufacturing processes, environmental impact, and cost analysis. This article will discuss these key factors in detail and explain their importance in the design o...
view more
-
Tsinghua University: Study on the Comprehensive Performance and Influencing Factors of Long Glass Fiber Reinforced PA66 Composites
2024-10-22
Introduction Fiber-reinforced polymer composites, due to their lightweight and high-strength characteristics, have found applications in many fields, especially in the transportation sector, where they can effectively reduce vehicle weight and better achieve energy savings and emission reductions. Among them, long glass fiber (LGF) reinforced polyamide materials (PA/LGF) are widely used in the man...
view more
e-mail
English
français
Deutsch
русский
italiano
español
português
العربية
日本語
한국의
中文